Yaesu FT-DX101MP

The Yaesu FT-DX101MP is the new long-awaited compact HF/50MHz 200W SDR Transceiver with external speaker. The FT-DX101MP has a frequency range on the TX: 1.8-54 MH and the RX: 30 kHz - 75 MHz.

Narrow band SDR

The Narrow band SDR receiver removes strong out-of-band signals using a super heterodyne method, with narrow band roofing filters that significantly attenuate unwanted out-of-band frequency components, and the desired signals within the passband are converted to digital through an 18-bit high-resolution A/D converter and sent to an FPGA (Field Programmable Gate Array) for signal processing.

Quiet and clear reception

Local oscillator system with ultra-low noise level; 400MHz HRDDS (high resolution direct digital synthesizer). Unparalleled -70 dB maximum attenuation VC-Tune. Newly developed VC-Tune RF Preselector with high-precision stepper motor drive offers excellent damping characteristics.

Highest transmission signal purity

The excellent C/N characteristics of the 400 MHz HRDDS (High Resolution Direct Digital Synthesizer) used in the local oscillator circuit also contribute significantly to the transmitter section. In a generic circuit, noise or distortion can occur depending on the circuit configuration and components, up to the final stage that produces the transmit signal, even if the local signal is of high quality. In the Yaesu FTDX101, a thorough examination of every element up to the final TX stage was carried out. The clock that divides and distributes the local signal of the 400MHz HRDDS circuit to each block, as well as the FPGA, D/A converter, the power amplifier, etc., and carefully selects the latest circuit configurations to improve the C/N characteristics to improve the entire channel block. The FTDX101's transmit signal is generated directly by a 16-bit D/A converter without going through a mixer circuit, significantly reducing distortion and noise.

Scope display 3DSS 7-inch TFT color screen

Intuitive insight into changes in signal strength Newly developed 3DSS (3-Dimentional Spectrum Stream) system in addition to a conventional waterfall display.

ABI (Active Band Indicator)

When the band is selected as MAIN band, the LED indicates white and when the band is selected by the SUB band, the LED indicates blue. When in transmission status, the LED turns red so you can immediately confirm which VFO is transmitting.

MPVD (Multi-Purpose VFO Outer Dial)

The MPVD is a large high-quality aluminum multi-function ring around the outside of the VFO dial. The ring allows control of SUB VFO frequency selector, VC-TUNE, Clarifier and C/S (custom selection function). The MPVD is a convenient dial that allows you to adjust key functions in ever-changing HF communications without taking your hand off the VFO. The ring has the traditional Yaesu excellent smooth and solid feel when used

PC remote control software to extend the working range

PC control software-implemented remote control of the transceiver from a remote location via the LAN or Internet is available. (requires optional external LAN Unit)

Features Yaesu FT-DX101MP

• Frequency range:
  
  • TX: 1.8-54 MHz
    
  • RX: 30kHz - 75MHz
• Display: 7 inch TFT color screen with touch screen
• Bandwidth: SSB: 3 kHz / CW: 500 Hz / AM: 6 kHz / FM: 16 kHz
• Broadcast mode: A1A (CW) / A3E (AM) / J3E (SSB) / F2D (FM) / F3E (FM) / F1B (RTTY) / G1B (PSK)
• Digital Noise Reduction (DNR): The Digital Noise Reduction (DNR) system is designed to reduce the level of ambient noise on the HF and 50 MHz bands
• Quick Memory Bank (QMB): The current operating status can be saved in a special memory channel with one touch (QMB: Quick Memory Bank)
• Intercept Point Optimization (IPO): The IPO function can determine the gain of the RF amplifier section to accommodate the connected antenna and received signal conditions
• Automatic Gain Control (AGCl): The AGC system is designed to help compensate for fade and other propagation effects
• Roofing Filter Switching (R.FIL): Displays the bandwidth of the currently selected roof filter (600 Hz, 3 kHz and 12 kHz)
• VFO/memory scan:
• Programmable Memory Scan (PMS): The PMS feature is especially useful in helping observe operational subband limits applicable to your amateur license class
• Digital Noise Reduction (DNR): The Digital Noise Reduction (DNR) system is designed to reduce the level of ambient noise on the HF and 50 MHz bands
• Digital NOTCH Filter (DNF): The Digital NOTCH Filter (DNF) is an effective beat-cancelling filter that can cancel out some disturbing beat notes in the receiver's passband
• IF NOTCH Filter (NOTCH): The IF NOTCH filter is a highly effective system that allows you to remove an interfering beat note or other carrier signal from the receiver's passband
• Contour (CONT): The Contour filter system causes a slight distortion of the IF filter passband
• Audio Peak Filter (APF): During CW operation, when interference or noise is present, the center frequency is automatically set to the PITCH frequency, making it easier to hear the desired signal
• AF / RF Gain / Squelch
• Noise Blanker
• Time-Out Timer (TOT): The "Time-Out Timer" (TOT) turns the transmitter OFF after continuous transmission for the programmed time
• Band Stack: The FTDX101 uses a triple-band stack VFO selection technique that allows up to three favorite frequencies and modes to be stored in each VFO band register
• External Phone Jack: Connect headphones to this standard φ3.5 stereo jack
• MicroSD card slot
• External speaker connection
• External tuner connection
• External RTTY/DATA connection
• External ground socket
• External REM Connection
• External AF-OUT Connection: receive audio output ±300 mVp-p
• External RX-OUT bus
• External IF-OUT bus
• External linear socket
• External TX-GND bus
• External USB Connection
• External USB Connection
• External KEY Connection
• External PTT Connection
• External display connection
• External ACC Connection
• External ALC Connection
• External analog meter socket
• Antenna connection: 3x UHF (PL) Female (SO-239)
• Length (radio unit): 322 mm
• Height (radio unit): 130 mm
• Width (radio unit): 420 mm
• Weight (radio unit): 14,300 grams
• Wide and narrow bandwidth selection
• Operating temperature: 0℃ to +50℃
• Frequency steps: SSB/CW: 1 Hz / 5 Hz / 10 Hz
• Frequency steps: AM/FM: 10 Hz / 100 Hz
• Frequency stability: ±0.1 PPM
• Operating voltage: AC 230 V
• Microphone connector: 8-pin
• Power consumption:
  • RX (no signal): 100 VA
  • RX (signal present): 120 VA
  • TX (200W): 720 VA
• Speaker dimensions: L 320 mm x H 130 mm x W 160 mm
• Speaker weight: 5000 grams

Transmitter

• Output power (Watt): SSB, CW, FM: 5-200 Watt / AM: 5-25 Watt
• Modulation type: J3E / A3E / F3E
• Maximum deviation: wide: ±5.0 kHz / narrow: ±2.5 kHz
• Harmonic radiation 1.8 - 29.7 MHz: Better than -50 dB
• Harmonic radiation 50 MHz (200W): Better than -63 dB
• Antenna impedance (antenna tuner 'OFF'): 50 Ω (unbalanced
• Antenna impedance (antenna tuner 'ON') 1.8-29.7 MHz: 16.7-150 Ω (unbalanced)
• Antenna impedance (antenna tuner 'ON') 50 MHz: 25 - 100 Ω (unbalanced)
• Microphone impedance: 600 Ω (200 - 10k Ω)
• SSB Carrier Suppression: Minimum 60 dB below peak output
• Unwanted sideband suppression: minimum 60 dB below peak output
• Audio response SSB: no more than -6 dB from 300 - 2700 Hz

Receiver

• Sensitivity 1.8-30 MHz SSB/CW: 0.16 μV type for 10 dB SINAD (AMP2 “ON”) (2.4 kHz)
• Sensitivity 50-54 MHz SSB/CW: 0.125 μV type for 10 dB SINAD (AMP2 “ON”) (2.4 kHz)
• Sensitivity 70-70.5 MHz SSB/CW: 0.125 μV type for 10 dB SINAD (AMP2 “ON”) (2.4 kHz)
• Sensitivity 0.5-1.8 MHz AM: 6.3 μV type for 10 dB SINAD (AMP2 "ON") (30% modulation, 6.0 kHz / @ 400Hz)
• Sensitivity 1.8-30 MHz AM: 2.0 μV typ for 10 dB SINAD (AMP2 "ON") (30% modulation, 6.0 kHz / @ 400Hz)
• Sensitivity 50-54 MHz AM: 1.0 μV typ for 10 dB SINAD (AMP2 "ON") (30% modulation, 6.0 kHz / @ 400Hz)
• Sensitivity 70-70.5 MHz AM: 2.0 μV type for 10 dB SINAD (AMP2 "ON") (30% modulation, 6.0 kHz / @ 400Hz)
• Sensitivity 28-30 MHz FM: 0.25 μV typ for 12 dB SINAD (AMP2 “ON”)
• Sensitivity 50-54 MHz FM: 0.20 μV typ for 12 dB SINAD (AMP2 “ON”)
• Sensitivity 70-70.5 MHz FM: 0.25 μV type for 12 dB SINAD (AMP2 “ON”)
• Center frequency 1st: Main: 9.005 MHz / Sub: 8.9000 MHz
• Center frequency 2nd: Main: 24 kHz / Sub: 24 kHz
• Selectivity (-6 dB/-60 dB) CW (BW=0.5 kHz): 0.5 kHz or better / 0.75 kHz or less
• Selectivity (-6 dB/-60 dB) SSB (BW=2.4 kHz): 2.4 kHz or better / 3.6 kHz or less
• Selectivity (-6 dB/-60 dB) AM (BW=6 kHz): 6.0 kHz or better / 15 kHz or less
• Selectivity (-6 dB/-60 dB) FM (BW=12 kHz): 12 kHz or better / 30 kHz or less
• Reception system: Superheterodyne with double conversion
• Secondary radio wave strength: ≤4 nW
• Audio output power: 2.5 W (THD10%, AC 230 V)
• Audio output impedance: 4 - 16 Ω (nominal: 4 Ω)
• Image suppression 1.8-28 MHz: 70 dB or better
• Image suppression 50-54 MHz: 60 dB or better

Remark

This transceiver consists of a transceiver and a separate speaker (see product photo, where you see the separate speaker on the left side next to the transceiver)

Package contents

• 1x Yaesu FT-DX101MP (1x transceiver and 1x speaker)
• 1x 6.3 mm 3-contact plug / 3.5 mm 3-contact plug / RCA plug
• 1x Yaesu SSM-75E microphone
• 1x Spare fuse 25 Amp.
• 1x Manual in English